The cylinder was adjusted to the water level because that kept the pressure on the tube and the water inside at a constant rate throughout the tube. If the graduated cylinder had not been adjusted, the test would have been introduced to a random error because it would have been a flaw that was always present and would affect the measurements of the experiment. When the unknown anti-acid was tested the first time, the results yielded a 40.2% yield of CO2. The second trial of part B was not as accurate due to using a mass of the unknown-acid that was too small for accurate results. The lack of accuracy came from a lack of precision which resulted in a human error because the amount that was broken off and selected for the trial was too small.
Rocks are intriguing to many individuals all over the world. Being made up of one or even many minerals, rocks draw an overwhelming amount of attention to themselves. When a probe brought back samples of rock from Planet X the task of identifying the rock was assigned. With no prior knowledge of the type of rock presented one will need figure out the identity of the rock based only on its density and physical properties. With an experimental process, one will begin to compare and uncover the identity of the rock samples brought back.
With following the procedure, the experiment was completed very easily. The technique used worked very well. The graduated cylinder were dried after each trial to ensure each water level was equal. The air bubble were risen to the top to ensure the equal amount was measured. Systematic errors can not be eliminated by averaging In principle, they can always be eliminated by changing the way in which the experiment was done.
This finding could have been due to experimental errors which affected the results. Discussion
This cave is located 1000 feet underground and contains many of the largest natural gypsum crystals in the world (2). These pillars of selenite gypsum measure up to 50 feet long and 4 feet in diameter (1). These crystals were able to form in such huge quantities because the area was submerged in water that was rich in minerals as well as having a high stable temperature of 136 degrees Fahrenheit (2). The water had an abundant amount of anhydrite and, because of this environment, it dissolved into gypsum and formed these massive crystals (2). The water has since drained out of the caves and the air in the caves normally stays between 45 and 50 degrees Celsius and the humidity levels range from 90 to 100 percent (3).
In the lab “All That Glitters” the objective that was focused on during the lab was calculating the density, volume and mass of various substances. The method that was used in finding the volume of the samples is called the displacement method. This is a process where the volume of the water in the graduated cylinder is calculated before and after the sample is placed. In this lab, the goal of the experiment was to identify and come to consensus about what the unknown substance might be. For this experiment, the required materials were ten pre and post pennies, unknown sample, graduated cylinder, weigh boat, water, paper towels and a weighing scale.
Some ways to improve the lab are to make sure that the error sources are fixed. Next time, it should be imperative that the table being used is perfectly balanced and that the tape is not placed on the inside
The actual data is the result on our experiment vs theoretical, which is based on the calculations above. I have also learned to pay more attention to draining out all of the product completely before continuing to test the experiment, as any small drop of contaminant can veer our results into a different
Some errors would be that the timing of the pendulum swinging was off. And the length of the pendulum may have not been
For example, in the response experiment, a yeast solution was prepared without sugar mistakenly and thus had to be prepared again. This suggests that other errors in preparation and measurement could have been encountered. For the future, careful measurements using clean uncontaminated flasks would eliminate possibilities of such error. A source of error for the metabolism experiment involves the yeast’s yellow hue. It is possible that the color of the yeast caused the solution to look more
All sources I have used in this paper, are from the Internet. I have compared information from different angles to try to get a comprehensive and “objective” view of the experiment. A main source of information is the report from Dr Zimbardo whom was in charge of the experiment. Information is also collected from
Science Essay- Draft The purpose of this report is to explain and identify the three groups that rocks are classified into and how they are formed. Rocks can be classified as Igneous, metamorphic, and sedimentary. Metamorphic rocks are formed when other rocks are hot or pressurised. The process of rocks changing is called metamorphism.
Materials 1 calibrated thermometer, 1 scale that reads mass, 2 Styrofoam cups, 1 small lead sinker, boiling water in a beaker, 1 pair of kitchen tongs, 1 small cooking pot, stove top, distilled water, and 1 pair of safety goggles (I did not use a cork stopper). III. Procedure First, the beaker
The scientists take careful looks at the rocks to study things like texture, composition, and where the rock came from (OI). That helps them figure out what type of rock it is and what it is useful for. That is why the
In this experiment, the amount of water lost in the 0.99 gram sample of hydrated salt was 0.35 grams, meaning that 35.4% of the salt’s mass was water. The unknown salt’s percent water is closest to that of Copper (II) Sulfate Pentahydrate, or CuSO4 ⋅ 5H2O. The percent error from the accepted percent water in CuSO4 ⋅ 5H2O is 1.67%, since the calculated value came out to be 0.6 less than the accepted value of 36.0%.This lab may have had some issues or sources of error, including the possibility of insufficient heating, meaning that some water may not have evaporated, that the scale was uncalibrated, or that the evaporating dish was still hot while being measured. This would have resulted in convection currents pushing up on the plate and making it seem lighter by lifting it up
