While the solution dissolved, 50 mL of distilled water was added to a 150 mL beaker and heated on the hot plate. When the solution started to boil 2.65 grams of Na2SiO3*5H2O was added to the beaker with a stir bar and heated to a gentle boil. When both solutions began to boil, the sodium silicate solution was slowly added to the sodium aluminate. The solution was kept at 900C for 60 minutes and stirred with stir bar. After 60 minutes, the zeolite solution was cooled for 5 minutes and for the magnetized zeolite , 0.78 grams of FeCl3 and 0.39 grams of FeSO4*7H2O was added to the flask and stirred until the iron parts dissolved.
The design relied on two Schmitt triggers to generate the two different tones while using the transistors to act as a switch. This causes it to trigger continuously between two unstable states, allowing automatic switching between two frequencies producing two different tones. The RC values between the two Schmitt triggers will differ. Capacitors charge and discharge faster when it’s resistance is smaller.
2.4 Band Division and Energy Computation: The power spectrum of the signal is multiplied by magnitude response of set of 33 triangular band pass filters and in the range 300Hz-2000Hz. Sub-bands are formed by using the logarithmic spacing. The positions of these filters are equally spaced along the Mel frequency, which is related to the common linear frequency f by following formula: Mel (f) = 1125* ln (1+f/700) (3) Mel frequency is proportional to the logarithm of linear frequency and which is close to the human perceptual system. 2.5 Sub Fingerprint Generation:
Experiment 7 In this experiment we configured several DC circuits consisting of an emf and a network of resistors. The circuits were composed of a power supply, two DMMs, a circuit board, an SPST switch, and an assortment of known resistors along with one unknown resistor. We measured the current and voltage of the entire circuit as well as the potential drops across each resistor to determine the parameters of the circuit including the resistance, voltage, and current for each component.
%% Init % clear all; close all; Fs = 4e3; Time = 40; NumSamp = Time * Fs; load Hd; x1 = 3.5*ecg(2700). ' ; % gen synth ECG signal y1 = sgolayfilt(kron(ones(1,ceil(NumSamp/2700)+1),x1),0,21); % repeat for NumSamp length and smooth n = 1:Time*Fs '; del = round(2700*rand(1)); % pick a random offset mhb = y1(n + del) '; %construct the ecg signal from some offset t = 1/
1. Identify the range of senses involved in communication • Sight (visual communication), Touch (tactile communication), Taste, Hearing (auditory communication), Smell (olfactory communication) 2. Identify the limited range of wavelengths and named parts of the electromagnetic spectrum detected by humans and compare this range with those of THREE other named vertebrates and TWO named invertebrates. Figure 1: the electromagnetic spectrum source: www.ces.fau.edu Vertebrates Human Japanese Dace Fish Rattlesnake Zebra Finch Part of electromagnetic spectrum detected ROYGBV (visible light) detected by light sensitive cells in the eye called rods and cones.
Pure ASA crystals are isolated from the solution with a Hirsch Funnel that was used with a filter. The melting point of the pure ASA crystals were calculated in order to calculate of absorbance. Iron (III) salicylate dianion must contain the acidified solution Fe3+ in order to measure the absorbance values. The level of the impurity can
The serial 2-fold dilution were done with a volumetric pipette, its pump, and 10 mL volumetric flasks. Eight different solutions were produced, half of which came from Red 40 and the other half, from Blue 1. These different concentrated solutions were placed in a 10 mL volumetric flask, each labelled with either R for Red 40
Elijah Brycth B. Jarlos IX-Argon 1. Multicellularity is a condition of an organism to have multicellular cells. An example of a organism who has multicellular cells are plants, animals, and humans. The main reason of why scientists have a hard time finding a good set of existing organisms to compare. Is neither the first set of organisms which is being compared is dying as fast as the second specimen is being examined or they just can’t find the right species.
Lastly, the unknown compound was reacted with two different salts. For the first salt, 0.50 grams of KCl was mixed with 5 mL of water in one beaker while 0.5 grams of NaNO3 was mixed with 5 mL of water in a different beaker. Then, the NaNO3 solution was added to the KCl solution. To perform the reaction with the second salt, 0.50 grams of KCl was mixed with 5 mL of water and 1 mL of 1 M Ag(NO3)2 was added. After performing each reaction, the solution was observed to see if a reaction occurred and the pH value of the resulting solution was tested using a pH
The appearance after this period resulted in another color change back to white. The crucible, lid, and hydrated copper sulfate was weighed again to calculate the mass of water lost by dehydration (described in table 1.3). This was done by subtracting the final mass by the initial mass of the crucible, lid, and compound. The mass of the crucible would remain unchanged while the mass of the compound would be altered. This trial was repeated 3 times and 1 extra set of data was taken from 2 separate groups to include
Hypothesis: Increasing substrate concentration will increase the initial reaction rate until it stops increasing and flattens out. Independent Variable: Substrate concentration Dependent Variable: The substrate itself, 1.0% Hydrogen Peroxide How Dependent Variable will be Measured: Hydrogen Peroxide will be used in every experiment, just with different test tubes. The amount of Hydrogen Peroxide in the mixing table is the amount that will be added to each test tube.
The 250 mL beaker was rinsed well with the distilled water. The titration procedure above was repeated 2 more times with fresh potassium acid
Afterwards, have the flask sit on the wire guaze on the iron ring and stand and attach it to the distillation
Again select the flask and select Distillation Head from the drop down menu. ➢ For the third time select the flask and choose Condenser from Distillation from the menu and for last time select the flask Distillation Take-off from the dropdown option. ➢ Select the 100 mL Graduated Cylinder from the Equipment option and put it underneath of distillation take-off.