I need to find the area of rectangle ABCD. I know that ABCD is a rectangle with diagonals intersecting at point E. Segment DE equals 4x-5, segment BC equals 2x+6, and segment AC equals 6x. I predict that To find the area of rectangle ABCD I need to find out the base and height of the rectangle. The first step is to find what x equals. Since I know the intersecting line segments AC and DB are congruent that means when I times the equation 4x-5 for segment DE by two it will equal the equation 6x for segment AC.
Write 9-4x^2-x+2x^4 in standard form You first look at all the the numbers in the polynomial and see which coefficient has the highest number exponent. (the degree) which is 2x^4. Then you keeping descending down so -4x^2 would be next. Then you look at the numbers and variables in the problem, all you have left is 9 and -x you always put the variable first so it would be -x, then 9. So your answer would be
%% Init % clear all; close all; Fs = 4e3; Time = 40; NumSamp = Time * Fs; load Hd; x1 = 3.5*ecg(2700). ' ; % gen synth ECG signal y1 = sgolayfilt(kron(ones(1,ceil(NumSamp/2700)+1),x1),0,21); % repeat for NumSamp length and smooth n = 1:Time*Fs '; del = round(2700*rand(1)); % pick a random offset mhb = y1(n + del) '; %construct the ecg signal from some offset t = 1/
Using the data provided in each one of these tests it can be assumed that one has done the steps to be able to determine the magnitude and orientation of the charges of the tape in each test, thus, allowing them to apply the same principle to any object they so desired. Their results would line up with the following; that if the two pieces of tape are torn from the same 40 centimeter strip then the tops of both pieces of tape would be positive and the bottoms of both pieces of tape would be negative and that if they would double the tape the attraction or repulsion in general would lower due to the increased density. Their data would also show that two pieces of tape ripped from each other would result in one piece being entirely positive and the other being entirely negative, they would also be able to state that the orientation of how the tape is paired up doesn’t matter.
Results The lab experiment was done in two parts, one with the NAND, NOR, XOR and Hex Inverters and the other with a 7483 full adder gate, both will verify the truth table when two input bits and a carry are added together. The circuits were built by examining the 1 bits through a K-Map to create a Boolean expression for the sum and carry. The Boolean expression for the sum was A⊕B⊕C and the carry as AB+BC_in+AC_in. From these two expressions, we notice that we must use two exclusive-ORs gates in the sum inputs for A, B, and C. For the sum, we have to use NOR and NAND (the only available gates from the lab manual).
The more number of bases n is checked against, the more certain we can be that it is prime. The Miller-Rabin test is based on Fermat’s little theorem, with several optimizations. Similar to the Solovay-Strassen test, even numbers are discarded are these cannot be primes anyway and decreases the number of possible misdetections.
Part I Which of the concepts in these chapters was the most difficult for you? In 5-7 sentences, explain what you think you understand and ask 2-3 questions about things you know you don 't understand. Standard error of the mean I read the section on standard error of the mean (SEM) three times and unfortunately, this concept is difficult for me to understand. I do understand that the standard error of the mean is the standard deviation of a sampling distribution of means. I understand how to calculate the SEM (simply divide the standard deviation of the sample by the square root of the sample size minus one).
Figure shows the intersection of line joining the camera center and image points ${\bf x}$ and ${\bf x'}$ which will be the 3D point ${\bf X}$.\\ \end{figure} The ‘gold standard’ reconstruction algorithm minimizes the sum of squared errors between the measured and predicted image positions of the 3D point in all views in which it is visible, i.e.\\ \begin{equation} {\bf X=\textrm{arg min} \sum_{i} ||x_i-\hat{x_i}(P_i,X)||^2} \end{equation} Where ${\bf x_i}$ and ${\bf \hat{x_i}(P_i,X)}$ are the measured and predicted image positions in view $i$ under the assumption that image coordinate measurement noise is Gaussian-distributed, this approach gives the maximum likelihood solution for ${\bf X}$. Hartley and Sturm [3] describe a non-iterative
(a) 3Mbps / 150Kbpa =3 X 1024 / 150 = 3072 / 150 =20.48 20 Users can be supported 150Kbps dedicated. (b)
5. Public trials and executions serve as a deterance of deviant behaviors. These sanctions act as a way to set an example and for people to see what will happen to them if they do the same thing, These sanctions can also be seen as reinforcing boundaries. Although public executions and trials in “town square” are not as common in most countries today, the media is utilized to fulfil the same purpose. When there are high profile cases going on in the United States often tmes the full trial and sentancings are televised so that much of society can see what the repercussions are for defying a social norm.
When 70 volts at 60 cycles a second was placed upon the animals’ skin, the shivering stopped.
Chem 111 Post-Exam Self-Assessment See the instructions in Canvas for more details about how this assignment will be scored. 1. Fill in these blanks: Exam Number __3__ Your Predicted Exam Score _75_% Actual Exam Score _77.67% Current Course Score _
Ethics, the moral principles that guide one's compass, is a crucial topic throughout history and more so in today's technological world. As our studies are centered around this, the author will discuss the ethical implications in his profession, nondestructive testing or simply NDT. In this essay, the author will discuss what NDT is, why ethics are an integral part of this profession and the implications a breach of ethics may have. Nondestructive testing, NDT, is the testing and analysis of materials, components, and systems to ensure mechanical and material quality is met without the need for damaging the item.
The productions of the participants were digitally recorded and online perceptual judgments of segmented and intersegment distortions of accuracy were made by clinician. This helps the clinician and patients see if they hit a target with a red or green light. The study was reviewed by two judges for variability. Inter and intra judge reliability for perceptual accuracy was high. The average for 3STM’s was 88% from one judge and 95% from the other judge.
Reaction Kinetics: The Iodine Clock Reaction Kinetics is the study of the rates of chemical reactions. A reaction rate describes the reaction’s speed, it is the rate at which the starting materials of a reaction (reactants) react and transform into the final produced materials (products). The greater the reaction rate, the less time required for reactants to be converted to products. Understanding the factors and conditions influencing reaction rates of is of fundamental importance in industrial chemistry where the production of chemicals must be efficient and economical to maximise profits.
